☎ +33 9 70 75 50 24|contact@michaud-export.com
FacebookYouTubeLinkedIn
OUR CATALOGUES

  • Street light set

    1,00€
    The street light set is designed to interconnect a network with a street light installation inside a lighting column. The end cap is designed to ensure street light conductor insulation when fitted at its end. It is mainly used on the bottom of lighting column.
    Select options Details

  • Short-circuiting lost end BPMCC

    1,00€
    This accessory is designed to short-circuit waiting networks without power. It is used to warn accidental powering at one end. It ensures cables watertightness.
    Select options Details

  • Service repairing junction kit – JRB

    1,00€
    This accessory is designed to repair connection of service underground damaged cables.
    Select options Details

  • Aluminium earth cable and accessory

    1,00€
    The earth distributor is used to connect floor earths between themselves. It is installed in a building pillar according to applicable specifications. The ground cutting blade is installed at the bottom of the earth pillar. It enables the earth system opening during an earth resistance measurement.
    Details

  • Cable tie

    1,00€
    The cable tie is designed to tighten the phase and neutral conductors in order to achieve correct installation. It is used to prevent the conductors from rubbing against accessories such as clamps.
    Select options Details

  • Seal

    1,00€
    The seal is designed to be installed on electrical equipment, water meters, gas meters, etc. The breaking of the link enables to highlight a potential fraud. The sealable screw cover is designed to seal a screw.
    Select options Details

  • IRO tube

    1,00€
    The IRO tube is used outside to allow mechanical protection round electrical cables. The junction sleeve allows to connect two IRO tubes. The connection sleeve allows a connection between the sheath and the general protection box. The T-sleeve and the elbow allow connection and adaptation of the circuit of the tubes. The mounting bracket allows to set the sheath beside a facade.
    Select options Details

  • Cable saddle

    1,00€
    The cable saddle (facade) is designed for fixing the low voltage A.B.C. (Aerial Bundled Conductors) on façades using neutral messenger or fully supported technology. A cable saddle is implemented every 30cm to ensure excellent fixing of the A.B.C. The wall mounting is quick and easy to implement. It is discreet and aesthetic. The cable saddle (pole) is used to fix cable trunking on poles. It is fixed using a strap and it is made of UV protected thermoplastic material. The N733 is sealed with a cable tie for 15 to 30mm diameter cables, the N734 for 30 to 50mm diameter cables, and the N735 for 50 to 90mm cables.
    Details

  • Mechanical fixing

    1,00€
    The anchoring assembly is used for single or double dead-ending of A.B.C (aerial bundled conductors) with insulated neutral messenger. Two different sections of neutral messenger are available: 54.6mm² and 70mm²
    Details

  • Personal protective equipment – gloves

    1,00€
    These equipment aim to protect hands during installation works. The insulating gloves are designed to protect against electrical shocks during powered works.
    Details

  • Heat-shrinkable material

    1,00€
    This heat-shrinkable material is designed for low voltage applications in order to protect conductors and make them watertight. It is characterised by its insulating performances and its high resistivity to pollution and UV. It is retracted by blow torch heating.
    Select options Details

  • Bare lug

    1,00€
    The tubular lug is designed to connect cable. It is made of tinplated copper (by electrolysis). It is manufactured with an inspection hole and socketing. It is implemented with hexagonal compressed connection. It allows copper and aluminium conductors. This lug meets the requirement of the NFC 20-130 standard. The friction welded lug is used to connect aluminium bare conductors to copper equipment terminals. It is used for industrial or indoor applications. This lug is implemented by crimping and out of traction. This lug meets the requirement of the NF C 63-061 standard. The Al/Cu tinned aluminium lug is used to connect aluminium bare conductors to copper equipment terminals. It is applied with a deep crimping.
    Select options Details
Go to Top